Torque Test Tools

Torque test tools are the bench testers and analysers that measure the torque a hand or powered tool actually delivers, used for incoming checks, periodic verification and audit testing. Models range from simple go/no-go testers to full analysers that capture click points, run-down curves and residual torque. Capacity, the tool types tested and the depth of analysis needed guide selection.

TTC Torque Tool Tester

Verification and calibration of wide range of torque wrenges and torque tools
Ranges up to 800 Nm
Selectable engineering units: N-cm, N-m, in-lb, ft-lb, kg-cm (depending on range)

TT-QC Torque Tool Tester for quick tool inspection

Bench mount torque tester for quick tool verification
Ranges up to 1355 Nm
Eight selectable engineering units: Oz.in., Lb.in., Lb.ft., Nm, cNm, KgfCm, gfCm, Kgfm

TC-DT Torque tool tester with interchangeable loadcells

Interchangeable load cells with external display unit
Measuring range: 5 Ncm up to 2000 Nm
Selectable measuring units: Ncm, Nm, Oz.in, Lb.in, Lb.ft, Kgf.cm, Kgf.m

DI-1M Digital Torque Tester for Air Tools & Impact Wrenches

Air Tool & Impact Wrench Digital Torque Tester
4 Ranges up to 362.0 lb-ft / 50.00 kg-m / 500.0 N-m
Selectable Units: lb-ft, kg-m and N-m
NOTE: This Torque Tester is not CE certified

TT-QCM Torque Tool Tester for torque tool calibration

Verification and calibration of wide range of torque wrenges and torque tools
Ranges up to 2710 Nm
Eight selectable engineering units: Oz.in., Lb.in., Lb.ft., Nm, cNm, KgfCm, gfCm, Kgfm

MTM Multi-Range Torque Tester

Multi-Channel Torque Tester for Power Drivers & Wrenches
18 Ranges up to 6780 Nm
Eight selectable engineering units: Oz.in., Lb.in., Lb.ft., Nm, cNm, KgfCm, gfCm, Kgfm
Programmable high/low setpoints

TL-IT Inline Torque Limiter

Specified Preset
Typical Lifespan: 40.000 Cycles
Includes NIST Traceable Calibration Cert
Torque Ranges: from 0.33 Nm up to 339 Nm

Series-TT02 Torque Tool Tester for (Electric) Screw Drivers

Torque Tester for Hand Tools
4 ranges up to 1150 Ncm
Units of measure: Ncm, Nm, ozFin, lbFin, lbFft (selectable)
USB, RS-232, Mitutoyo (Digimatic) and analog outputs

TT-3000 Series Torque Testers with 16 measurement ranges

Torque Tester for testing click, dial, and digital wrenches, plus most power tools including impulse and DC electric
16 Ranges up to 1016 Nm
Eight selectable engineering units: Oz.in., Lb.in., Lb.ft., Nm, cNm, KgfCm, gfCm, Kgfm
RS-232 output

QCMBS Torque Tester for Nutrunners

Test stand for power wrenches
2 measuring ranges up to 2710 Nm
Eight (8) selectable construction units: Oz.in., Lb.in., Lb.ft., Nm, cNm, KgfCm, gfCm, Kgfm
RS-232 data output
Complete system consisting of test stand, test device and screwdriver simulator

TT-CA Radius Arms / Torque Arms

TT-CA Radius Arms up to 2000 N-m
TT-CA-.1MA High Accuracy Calibration Arm 0.1 meter radius 11 N-m Max
TT-CA-.25MA High Accuracy Calibration Arm 0.25 meter radius 340 N-m Max
TT-CA-.5MA High Accuracy Calibration Arm 0.5 meter radius 750 N-m Max
TT-CA-1MA High Accuracy Calibration Arm 1.0 meter radius 2000 N-m Max
The radius arms are available in 2 versions:
High Accuracy Arms are for use with +/-0.25% tolerance transducers / Standard Accuracy Arms are for use with +/-0.5% tolerance transducers

TT-DA Insert-, and Drive Adapters

Insert-, and drive adapters
For calibration purposes

TT-QC-CC Waterproof Carrying Case

Waterproof Carrying Case for TT-QC

RDF Joint Simulators / Run Down Fixtures

Joint Simulators / Run Down Fixtures
Required for accurate torque measurement for power-driven torque controlled tools
They simulate the conditions found when using the tool in real-world conditions

Showing 14 item(s)